**************************************
** PDUX3 WAKEUP POWER CONFIGURATION **
**************************************

Edit this file with a simple text editor such as notepad.
Use the prefix '0x' for hexadecimal numbers.
DO NOT START DECIMAL NUMBERS WITH 0.

Lines beginning with [ are configuration parameters.
Edit the values after ] on those lines.
Do not change the order of those lines.
You may use two slashes to append notes // like this.
All other lines are ignored. You may insert lines anywhere
to add your own notes provided they do not begin with [.
NOTES YOU ADD ARE NOT STORED IN THE DEVICE.

[S0 : Device] PDUX3
[N1 : Format] 1

** ALWAYS ON / WAKEUP PIN NOT USED **

[N10 : PDU always on when logic power applied 0=NO 1=YES] 1

** WAKEUP PIN **

The WAKEUP pin always turns the PDU on immediately.

[N101 : Minimum PDU on time 0 to 60000 x0.01s] 300
[N103 : Validate to off time 0 to 60000 x0.01s] 100

** INPUT 13 **

[N200 : Enable wake on pin high 0=NO 1=YES] 0
[N201 : Minimum PDU on time 0 to 60000 x0.01s] 300
[N202 : Validate to on time 0 to 60000 x0.01s] 10
[N203 : Validate to off time 0 to 60000 x0.01s] 100

** INPUT 14 **

[N300 : Enable wake on pin high 0=NO 1=YES] 0
[N301 : Minimum PDU on time 0 to 60000 x0.01s] 300
[N302 : Validate to on time 0 to 60000 x0.01s] 10
[N303 : Validate to off time 0 to 60000 x0.01s] 100

** INPUT 15 **

[N400 : Enable wake on pin high 0=NO 1=YES] 0
[N401 : Minimum PDU on time 0 to 60000 x0.01s] 300
[N402 : Validate to on time 0 to 60000 x0.01s] 10
[N403 : Validate to off time 0 to 60000 x0.01s] 100

** INPUT 16 **

[N500 : Enable wake on pin high 0=NO 1=YES] 0
[N501 : Minimum PDU on time 0 to 60000 x0.01s] 300
[N502 : Validate to on time 0 to 60000 x0.01s] 10
[N503 : Validate to off time 0 to 60000 x0.01s] 100

** CAN ACTIVITY **

Wake on any CAN activity.

[N600 : Enable wake on CAN activity 0=NO 1=YES] 0
[N601 : Minimum PDU on time 0 to 60000 x0.01s] 300
[N603 : Validate to idle 0 to 60000 x0.01s] 200

** SPECIFIC CAN FRAME **

Wake on specific CAN frame requires more power in sleep.
Combine with N600 to avoid but will take two frames to wake.

[N700 : Enable wake on specific CAN frame 0=NO 1=YES] 0
[N701 : Minimum PDU on time 0 to 60000 x0.01s] 500
[N703 : Frame receive timeout 0 to 60000 x0.01s] 300
[N710 : CAN baud rate 50000 to 1000000 bps] 1000000
[N711 : CAN frame type 0=STANDARD 1=EXTENDED] 0
[N712 : CAN frame identifier] 0x7FF
[N713 : CAN frame minimum data length 0 to 8 bytes] 0
[N720 : CAN frame byte 0 mask] 0x00
[N721 : CAN frame byte 1 mask] 0x00
[N722 : CAN frame byte 2 mask] 0x00
[N723 : CAN frame byte 3 mask] 0x00
[N724 : CAN frame byte 4 mask] 0x00
[N725 : CAN frame byte 5 mask] 0x00
[N726 : CAN frame byte 6 mask] 0x00
[N727 : CAN frame byte 7 mask] 0x00
[N730 : CAN frame byte 0 value] 0x00
[N731 : CAN frame byte 1 value] 0x00
[N732 : CAN frame byte 2 value] 0x00
[N733 : CAN frame byte 3 value] 0x00
[N734 : CAN frame byte 4 value] 0x00
[N735 : CAN frame byte 5 value] 0x00
[N736 : CAN frame byte 6 value] 0x00
[N737 : CAN frame byte 7 value] 0x00

** CAN TERMINATION **

[N800 : Enable CAN termination resistor 0=NO 1=YES] 0

** END OF CONFIGURATION **

[E]